Section one: Contracting authority
one.1) Name and addresses
UNIVERSITY OF SHEFFIELD
Western Bank
SHEFFIELD
S102TN
Contact
James Noble
Country
United Kingdom
NUTS code
UKE32 - Sheffield
Companies House
RC000667
Internet address(es)
Main address
https://in-tendhost.co.uk/sheffield
one.3) Communication
The procurement documents are available for unrestricted and full direct access, free of charge, at
https://in-tendhost.co.uk/sheffield
Additional information can be obtained from the above-mentioned address
Tenders or requests to participate must be submitted electronically via
https://in-tendhost.co.uk/sheffield
one.4) Type of the contracting authority
Body governed by public law
one.5) Main activity
Education
Section two: Object
two.1) Scope of the procurement
two.1.1) Title
3631/JN - Spin Test Facility
Reference number
3631/JN
two.1.2) Main CPV code
- 38000000 - Laboratory, optical and precision equipments (excl. glasses)
two.1.3) Type of contract
Supplies
two.1.4) Short description
The University of Sheffield's Department of Electronic and Electrical Engineering and AMRC with funding from Innovate UK are looking to acquire a spin-test facility (also colloquially known as 'spin-rig') in support of research in high speed rotating components and assemblies. This capability will form part of a UK-wide network of facilities and capabilities which are available to UK industry and academia to further R&D and supply chain development in power electronics, machines and drives. Its principal role will be to facilitate mechanical testing, model validation and certification of high performance electrical machine rotors, including an ability to determine burst speeds and assess the nature of the burst. Although burst capability and overspeed testing is an essential requirement, much of the demand is driven by the need to characterise rotors and shaft assemblies in terms of radial growth at normal operating conditions and to characterise low-cycle fatigue. The system will consist of an evacuated chambers into which the test-piece is located and connected to a drive mechanism that enables its mechanical response to be quantified over a prescribed speed range as set out in the requirements section below. The facility will also be used in support of wider rotatives research across the University Sheffield, in many cases in collaboration with industry and/or academic partners, where likely use cases include inter-alia tool assemblies, compressor and turbine parts. The facility will be an R&D facility, in many cases testing one-of-a-kind test pieces and not a production facility and hence there is little or no premium in rapid / automated set-up of repeated tests. The equipment will be located in an existing industrial unit within the Advanced Manufacturing Research Centre (AMRC) which has a 400mm thick cast concrete floor, extensive services, large loading doors and a10 tonne overheard crane.
two.1.5) Estimated total value
Value excluding VAT: £1,058,000
two.1.6) Information about lots
This contract is divided into lots: No
two.2) Description
two.2.2) Additional CPV code(s)
- 38400000 - Instruments for checking physical characteristics
- 38500000 - Checking and testing apparatus
- 38900000 - Miscellaneous evaluation or testing instruments
two.2.3) Place of performance
NUTS codes
- UKE32 - Sheffield
two.2.4) Description of the procurement
The University of Sheffield's Department of Electronic and Electrical Engineering and AMRC with funding from Innovate UK are looking to acquire a spin-test facility (also colloquially known as 'spin-rig') in support of research in high speed rotating components and assemblies. This capability will form part of a UK-wide network of facilities and capabilities which are available to UK industry and academia to further R&D and supply chain development in power electronics, machines and drives. Its principal role will be to facilitate mechanical testing, model validation and certification of high performance electrical machine rotors, including an ability to determine burst speeds and assess the nature of the burst. Although burst capability and overspeed testing is an essential requirement, much of the demand is driven by the need to characterise rotors and shaft assemblies in terms of radial growth at normal operating conditions and to characterise low-cycle fatigue. The system will consist of an evacuated chambers into which the test-piece is located and connected to a drive mechanism that enables its mechanical response to be quantified over a prescribed speed range as set out in the requirements section below. The facility will also be used in support of wider rotatives research across the University Sheffield, in many cases in collaboration with industry and/or academic partners, where likely use cases include inter-alia tool assemblies, compressor and turbine parts. The facility will be an R&D facility, in many cases testing one-of-a-kind test pieces and not a production facility and hence there is little or no premium in rapid / automated set-up of repeated tests. The equipment will be located in an existing industrial unit within the Advanced Manufacturing Research Centre (AMRC) which has a 400mm thick cast concrete floor, extensive services, large loading doors and a10 tonne overheard crane.
two.2.5) Award criteria
Price is not the only award criterion and all criteria are stated only in the procurement documents
two.2.7) Duration of the contract, framework agreement or dynamic purchasing system
Start date
2 May 2024
End date
3 May 2024
This contract is subject to renewal
No
two.2.10) Information about variants
Variants will be accepted: Yes
two.2.11) Information about options
Options: No
Section three. Legal, economic, financial and technical information
three.1) Conditions for participation
three.1.2) Economic and financial standing
Selection criteria as stated in the procurement documents
three.1.3) Technical and professional ability
Selection criteria as stated in the procurement documents
Section four. Procedure
four.1) Description
four.1.1) Type of procedure
Open procedure
four.1.8) Information about the Government Procurement Agreement (GPA)
The procurement is covered by the Government Procurement Agreement: Yes
four.2) Administrative information
four.2.2) Time limit for receipt of tenders or requests to participate
Date
10 March 2023
Local time
12:00pm
four.2.4) Languages in which tenders or requests to participate may be submitted
English
four.2.6) Minimum time frame during which the tenderer must maintain the tender
Duration in months: 3 (from the date stated for receipt of tender)
four.2.7) Conditions for opening of tenders
Date
10 March 2023
Local time
12:01pm
Section six. Complementary information
six.1) Information about recurrence
This is a recurrent procurement: No
six.2) Information about electronic workflows
Electronic ordering will be used
Electronic invoicing will be accepted
Electronic payment will be used
six.4) Procedures for review
six.4.1) Review body
The University of Sheffield
Sheffield
S10 2TN
Country
United Kingdom